首页 诗词 字典 板报 句子 名言 友答 励志 学校 网站地图
当前位置: 首页 > 教程频道 > 网络技术 > 电脑技能 >

华为 ar2811 路由器 串口 down()

2013-01-09 
华为 ar2811 路由器 串口 down(在线等) 2811 wan口无法和对端设备1.1.1.2连接,Serial0/0 current state :U

华为 ar2811 路由器 串口 down(在线等)

 2811 wan口无法和对端设备1.1.1.2连接,
Serial0/0 current state :UP
Line protocol current state :DOWN
Description : Serial0/0 Interface
The Maximum Transmit Unit is 1500, Hold timer is 10(sec)
Internet Address is 1.1.1.1/30
Link layer protocol is PPP
LCP reqsent
Output queue : (Urgent queuing : Size/Length/Discards)  0/50/0
Output queue : (Protocol queuing : Size/Length/Discards) 0/500/0
Output queue : (FIFO queuing : Size/Length/Discards)  0/75/0
Physical layer is synchronous,Baudrate is 64000 bps
Interface is DCE, Cable type is V24
Last clearing of counters: Never
    Last 300 seconds input rate 0.00 bytes/sec, 0 bits/sec, 0.00 packets/sec
    Last 300 seconds output rate 2.09 bytes/sec, 16 bits/sec, 0.11 packets/sec
    Input: 0 packets, 0 bytes
          0 broadcasts, 0 multicasts
          0 errors, 0 runts, 0 giants
          0 CRC, 0 align errors, 0 overruns
          0 dribbles, 0 aborts, 0 no buffers
          0 frame errors
    Output:58 packets, 1044 bytes
          0 errors, 0 underruns, 0 collisions
          0 deferred
    DCD=UP  DTR=UP  DSR=UP  RTS=DOWN  CTS=UP

debug信息:
*0.475732 xxx PPP/8/debug2:
  PPP Event:
      Serial0/0 LCP TO+(Timeout with counter > 0)  Event
      state reqsent , Retransmit = 3
*0.475732 xxx PPP/8/debug2:
  PPP Packet:
      Serial0/0 Output LCP(c021) Pkt, Len 18
      State reqsent, code ConfReq(01), id 25, len 14
      MRU(1), len 4, val 05dc
      MagicNumber(5), len 6, val 0007a848
*0.485732 xxx PPP/8/debug2:
  PPP Event:
      Serial0/0 LCP TO+(Timeout with counter > 0)  Event
      state reqsent , Retransmit = 2
*0.485732 xxx PPP/8/debug2:
  PPP Packet:
      Serial0/0 Output LCP(c021) Pkt, Len 18
      State reqsent, code ConfReq(01), id 26, len 14
      MRU(1), len 4, val 05dc
      MagicNumber(5), len 6, val 0007abbb
------解决方案--------------------


对端的配置和相关信息呢?
[解决办法]
Show interface Serial0

看看!
[解决办法]
晕倒,怪我没说清楚,我是想要 联想那台设备的接口状态,这样才好对比!


[解决办法]
Serial0/0 current state :UP
Line protocol current state :DOWN
Physical layer is synchronous,Baudrate is 64000 bps

Serial0 is up, line protocoal is up
 Physical layer is Sync, MTU is 1500 bytes, BW 1544 Kbit

看见没有,联想设备默认的带宽配置是1.5Mb,华3是的64Kb,先把华3的配置改过来再说!
命令在接口下敲:baudrate ?根据提示输入正确的带宽值...
[解决办法]
应该有1.5吧

[解决办法]

引用:
把联想的路由器eth带宽改为10M后,也可以通,配置如下:


不知道你怎么想的...!风马牛不相干呀!
[解决办法]
引用:
把联想的路由器eth带宽改为10M后,也可以通,配置如下:


不知道你怎么想的...!风马牛不相干呀!
[解决办法]
哦哦,那结贴吧...

热点排行